View PLL702-03SM_1296561.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
FEATURES
* * * * * * * *
*
PIN ASSIGNMENT
Single Low EMI IC to replace multiple crystals and oscillators on Notebooks and Motherboards (27MHz, 8MHz, 12MHz, 24.576MHz, 25MHz). Single crystal input: 24.576MHz (accuracy requirement +/- 20ppm) Less than 10ppm Frequency Synthesis error, meeting AC97, IEEE1394, IEEE802 and USB2.0 frequency precision specification. 27MHz clock with 5 levels of Selectable Spread Spectrum modulation form +/- 0.5% to +/- 1.5% center. 25MHz clock with double drive strength (Ethernet PHY and MAC). 24.576MHz clocks for Audio Codec and IEEE1394. Selectable 12MHz (USB 2.0) or 8MHz (Keyboard controller). Dual power source selection for 24.576MHz, 8MHz, and 12MHz.
Available in 16-Pin SOIC or TSSOP.
VDDOSC XIN XOUT VSSOSC VSSB1 24.576MHz/SST0* T 24.576MHz/SST1* v VDDB1
1 2
16 15
VDDB2 27MHz VSSB2 8MHz 12MHz/VDD_SEL* v VSS25M 25MHzx2 VDD25M
PLL 702-03
3 4 5 6 7 8
14 13 12 11 10 9
Note: 25MHzx2: double drive strength *: Bi-directional pin v : Internal pull-down resistor (120k ) T : Tri-level input
Table 1. SPREAD SPECTRUM SELECTION
SST1 1 1 1 0 0 0 SST0 1 0 M 1 0 M SST Modulation only on 27MHz. (pin 15) +/- 1.5 % +/- 1.25 % +/- 1 % +/- 0.75 % +/- 0.5 % SST OFF (Default)
POWER GROUPS
* * * VDDOSC - VSSOSC: XIN, XOUT, analog core and digital part. VDDB1 - VSSB1: 24.576MHz. VDDB2 - VSSB2: 27MHz, 8MHz, and 12MHz. VDD25M - VSS25M: 25MHz, (also used for 12MHz, 8MHz when power VDDB2 is not present, and 24.576MHz when power VDDB1 is not present).
*
Notes: M = Do not connect. 1 = Pulled up. 0 = Pulled down.
Table 2. POWER SELECTION TABLE
VDD_SEL 0 1 24.576MHz (pin 7) VDDB1 VDD25M 12MHz (pin 12) 8MHz (pin 13) VDDB2 VDD25M
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 1
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
BLOCK DIAGRAM
VDDB2 SSC(0:1) XIN XOUT
XTAL OSC
PLL SST
27_14.318MHz VDD25M VDDB1 VDDB1
24.576MHz (pin7) 24.576MHz (pin6) 25MHz
VDD25M VDD25M VDDB2
PLL2
VDD25M VDDB2
12MHz
8MHz
Note: In order to use VDD25M as power source for 8MHz (pin 13), 24.576MHz (pin 7), and 12MHz (pin 12), it is necessary to select this feature through the VDD_SEL input (see Power Selection Table on p.1). Note 2: Only 27MHz output is modulated for low EMI via Spread Spectrum.
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 2
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
PIN DESCRIPTIONS
Name
VDDOSC XIN XOUT VSSOSC VSSB1 24.576MHz/SST0
Pin#
1 2 3 4 5 6
Type
P I O P P B
Description
3.3V power supply for oscillator, analog core and digital circuitry. Crystal input: for 24.576MHz fundamental crystal (CL = 20pF, parallel resonant mode, +/20ppm). On-chip load capacitors: no external load capacitors required. Crystal output. Ground connection. Ground connection. Bi-directional and Tri-Level pin. Upon power-on, the value of SST0 is latched in and used to select the SST control (see Spread Spectrum selection table 1). Tri level input: M = Do not connect, 1 = Pull up, 0 = Pull down. After power-up this pin acts as 24.576MHz output clock. Bi-directional pin. Upon power-on, the value of SST1 is latched in and used to select the SST control (see Spread Spectrum selection table 1). Internal pull down defaults SST1 to 0, use external pull-up to set to 1. After power-up this pin acts as 24.576MHz output clock. 3.3V power supply for 24.576MHz clock. 3.3V power supply for 25MHz, 8MHz, 12MHz, 24.576MHz. 25MHz Ethernet output clock (double drive strength). Ground connection. Bi-directional pin. Upon power-on, the value of VDD_SEL is latched in and used to select the power (see Power Selection table 2 ). Internal pull down defaults SST1 to 0, use external pull-up to set to 1. After power-up this pin acts as 12MHz output clock. 8MHz output clock (for Keyboard controller). Ground connection. 27MHz output. This output can be modulated for low EMI using SST (Spread Spectrum Technology). 3.3V power supply for 27MHz, 20MHz, 12MHz, and 24.576MHz.
24.576MHz/SST1 VDDB1 VDD25M 25MHzx2 VSS25M 12MHz/VDD_SEL 8MHz VSSB2 27MHz VDDB2
7 8 9 10 11 12 13 14 15 16
B P P O P B O P O P
FUNCTIONAL DESCRIPTION Tri-level and two-level inputs
In order to reduce pin usage, the PLL702-02 uses tri-level input pins. These pins allow 3 levels for input selection: namely, 0 = Connect to GND, 1 = Connect to VDD, M = Do not connect. Thus, unlike the two-level selection pins, the tri-level input pins are in the "M" (mid) state when not connected. In order to connect a tri-level pin to a logical "zero", the pin must be connected to GND. Likewise, in order to connect to a logical "one", the pin must be connected to VDD.
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 3
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
Connecting a bi-directional pin
The PLL702-03 also uses bi-directional pins. The same pin serves as input upon power-up, and as output as soon as the inputs have been latched. The value of the input is latched-in upon power-up. Depending on the pin (see pin description), the input can be tri-level or a standard two-level. Unlike unidirectional pins, bi-directional pins cannot be connected directly to GND or VDD in order to set the input to "0" or "1", since the pin also needs to serve as output. In the case of two level input pins, an internal pullup resistor is present. This allows a default value to be set when no external pull down resistor is connected between the pin and GND (by definition, a tri-level input has a the default value of "M" (mid) if it is not connected). In order to connect a bidirectional pin to a non-default value, the input must be connected to GND or VDD through an external pull-down/pull-up resistor. Note: when the output load presents a low impedance in comparison to the internal pull-up resistor, the internal pull-up resistor may not be sufficient to pull the input up to a logical "one", and an external pull-up resistor may be required. For bi-directional inputs, the external loading resistor between the pin and GND has to be sufficiently small (compared to the internal pull-up resistor) so that the pin voltage be pulled below 0.8V (logical "zero"). In order to avoid loading effects when the pin serves as output, the value of the external pull-down resistor should however be kept as large as possible. In general, it is recommended to use an external resistor of around one sixth to one quarter of the internal pull-up resistor (see Application Diagram). Note: when the output is used to drive a load presenting an small resistance between the output pin and VDD, this resistance is in essence connected in parallel to the internal pull-up resistor. In such a case, the external pull-down resistor may have to be dimensioned smaller to guarantee that the pin voltage will be low enough achieve the desired logical "zero". This is particularly true when driving 74FXX TTL components.
APPLICATION DIAGRAM: BI-DIRECTIONAL PINS WITH INTERNAL PULL-UP
Internal to chip VDD
External Circuitry
Rup Power Up Reset
R RB
Output
EN
Bi-directional pin
Clock Load
Latched Input
Latch
RUP/4
Jumper options
NOTE: Rup=Internal pull-up resistor (see pin description). Power-up Reset : R starts from 1 to 0 while RB starts from 0 to 1.
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 4
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
Electrical Specifications
1. Absolute Maximum Ratings PARAMETERS
Supply Voltage Range Input Voltage Range Output Voltage Range Soldering Temperature Storage Temperature Ambient Operating Temperature* TS TA -65 -40
SYMBOL
V CC VI VO
MIN.
MAX.
7 V CC +0.5 V CC +0.5 260 150 85
UNITS
V V V C C C
-0.5 -0.5 -0.5
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for INDUSTRIAL grade only. 2. AC Specification PARAMETERS
Input Frequency (to be set via XTAL_SEL) SST modulation sweep rate Output Rise Time Output Fall Time Duty Cycle Duty Cycle 8MHz clock Max. Absolute Period Jitter Max. Jitter, cycle to cycle 0.8V to 2.0V with no load 2.0V to 0.8V with no load At VDD/2 At VDD/2 Long term, No SST Long term + Short term 45 43 50 50
CONDITIONS
+/- 20ppm accuracy
MIN.
TYP.
24.576 28
MAX.
UNITS
MHz kHz
1.5 1.5 55 57 150 120
ns ns % % ps ps
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 5
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
3. DC Specification PARAMETERS
Operating Voltage Input High Voltage Input Low Voltage Input High Voltage Input Low Voltage Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Output High Voltage At CMOS Level Nominal Output Current Operating Supply Current Short-circuit Current
SYMBOL
VDD VIH VIL VIH VIL VIH VIL VOH VOL VOH IOUT IDD IS
CONDITIONS
Nominal voltage 3.3V
MIN.
2.97
TYP.
VDD/2 VDD/2
MAX.
3.63 VDD/2 - 1 0.5
UNITS
V V V V V V V V
For all Tri-level input For all Tri-level input For all normal input For all normal input IOH = -30mA (normal drive) IOH = -60mA (double drive) IOL = 30mA (normal drive) IOH = -60mA (double drive) IOH = -8mA Normal drive strength Double drive strength No Load
VDD-0.5 2 0.8 2.4 0.4 VDD-0.4 30 60 35 100
V V mA mA mA
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 6
Preliminary
PLL702-03
Low EMI Peripheral Clock Generator for Notebook PCs
PACKAGE INFORMATION
16 PIN Narrow SOIC, TSSOP ( mm )
SOIC Symbol A A1 B C D E H L e Min. 1.35 0.10 0.33 0.19 9.80 3.80 5.80 0.40 1.27 BSC Max. 1.75 0.25 0.51 0.25 10.00 4.00 6.20 1.27 0.45 Min. 0.05 0.19 0.09 4.90 4.30 TSSOP Max. 1.20 0.15 0.30 0.20 5.10 4.50 6.40 BSC 0.75 0.65 BSC B e A1 C L A D E H
ORDERING INFORMATION
For part ordering, please contact our Sales Department: 47745 Fremont Blvd., Fremont, CA 94538, USA Tel: (510) 492-0990 Fax: (510) 492-0991
PART NUMBER
The order number for this device is a combination of the following: Device number, Package type and Operating temperature range
PLL702-03 X C
PART NUMBER TEMPERATURATURE C=COMMERCIAL M=MILITARY I=INDUSTRAL PACKAGE TYPE O = TSSOP, S = SOIC
PhaseLink Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Phaselink is believed to be accurate and reliable. However, PhaseLink makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: PhaseLink's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of PhaseLink Corporation.
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
Rev 10/06/02 Page 7

▲Up To Search▲

Price & Availability of PLL702-03SM

	To Download PLL702-03SM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .